The following review was written on Apirl 30, 2009, but for some reaons Amazon broke the link between the product and the review, and was unable to link them back. Because many readers find the original review helpful, it is reposted here. Hope it will helpful to you as it was helpful to them:
The AMCO Advanced measuring cups and spoons are great. They are made with high quality thick 18/10 stainless steel. The steel is more than 1 mm thick, so they are heavy and sturdy. Each cup or spoon is made from a single-piece steel (no weld nor seam), so it is very easy to clean - a simply wipe will do. The size/volume markings are engraved into the metal, so they will not fade. I have uploaded a picture of a 1-cup for customer image. These tools should last you a lifetime.
Comparing to typical measuring cups, these cups are shorter and wider, which allow them to balance nicely on a flat surface. The ends of the spoon handles are bended downward, so the spoons can sit nicely on a flat surface. This comes handy from time to time, more so for cooking than baking - in my experience.
I feel there is a need to address some of the negative reviews here. While I agree with many of them, I do not experience some of the more detrimental ones.
I find my cups and spoons to be reasonably accurate. I used a graduating cylinder to measure the 1 cup because its filled weight exceeds the limit of the analytical balance. For the 1 cup which should equal to 236mL, I measured a volume of ~222mL. This is a -6% deviation. For the rest of the cups and spoons, I filled them with water and poured the water into a container for weight measurement. The weight is then converted back to volume via "1 gram of water = 1 mL of water". (These measurements were acquired from an analytical scale in a laboratory. These analytical scales are routinely calibrated and are more accurate than the typical kitchen scales.)
For the ½ cup (118mL), I measured a volume of 111.5mL (a -6% deviation).
For the 1/3 cup (79mL), I measured 84.8mL (+7%).
For the ¼ cup (59mL), I measured 61.8mL (+5%).
For the 1 tablespoon (15 mL), I measured 14.0mL (-7%).
For the 1 teaspoon (5mL), I measured three times and the averaged volume is 4.7mL (-6%).
For the ½ teaspoon (2.5mL), I measured 2.5mL (0%).
For the ¼ teaspoon (1.25mL), I measured 1.4mL (+12%).
Specifically, the 1 teaspoon measurement was repeated three times. The individual results were: 5.2mL, 4.5mL, and 4.3mL. This illustrates the variability introduced by a user -- human error. These cups and spoons appear to be adequate for ~10% accuracy.
I find the cups and spoons have smooth surface, and did not find any rough edge or surface as mentioned by other reviewers.
Now I will confirm some of the negative reviews. Yes, these cups and spoons are heavier than any I have seen. They are about 2-3 times heavier. Due to the fact that the cups are wider, you may also have difficulty to get them into containers with small opening. This is especially so for the 1-cup, which is 3-7/8 inches wide (I have upload a customer picture of it). Because the cups are shorter and wider, the potential for measurement error is higher. Imagine you have a tall bottle and a flat bowl. If you are 1 cm off from filling up the tall bottle, the relative error will be minor. However, if you are 1 cm off from filling up the flat bowl, the relative error will be large. Since these cups are about ½ the height of other cups, the potential human error is about 2-fold higher. One may say, these cups and spoons are technically accurate, but the potential human error is magnified.
*Update on Jun 26, 2010* Everything is working fine. Nothing is broken.
Enjoy fast, free delivery, exclusive deals, and award-winning movies & TV shows with Prime
Try Prime
and start saving today with fast, free delivery
Add a debit or credit card to save time when you check out
Convenient and secure with 2 clicks. Add your card
Frequently bought together
$15.10
Get it as soon as Tuesday, May 14
In Stock
+
Total price:
To see our price, add these items to your cart.
Choose items to buy together.
Similar items that may deliver to you quickly
Page 1 of 1 Start overPage 1 of 1
From the manufacturer
Kitchen Tools and Gadgets
Amco Kitchen Tools and Gadgets are crafted from premium materials for durability that will last. The classic nylon and stainless steel collection features a heavy-duty, stainless steel handle paired with a heat-resistant nylon head that is safe on all cookware, including non-stick. Available in singles or as a set, Amco has every necessary tool for dynamic food preparation.
Citrus Juicers & Juice Presses
With a variety of citrus juicers, Amco makes it easy to add fresh juice to recipes and more. Each citrus squeezer is crafted from heavy-duty metal, and ensures you get pure juice every time, no seeds or pulp. The counter top juicers allow you to squeeze fresh oranges, grapefruits and more for a refreshing beverage anytime of the day.
Measuring Tools
To ensure your recipes come out perfect every time, Amco features a large variety of measuring cups and spoons. Crafted from different gauges of stainless steel, there is a set of measuring tools for the beginner baker to the most advanced pastry chef. With special features such as magnetized nesting for easy, compact storage, or dual sided spoon for wet and dry measuring, Amco has you covered.
Specialty Tools & Gadgets
Never be caught without the perfect tool again! Amco has a large variety of tools that meet the special needs of certain foods. The Avocado Slicer and Pitter is dual sided to remove the pit and slice without damaging the fruit. A must have, the Rub-A-Way Bar is made from stainless steel and remove any odor from your hands, including onion, fish or garlic. The Peach Pitter/Slicer effortlessly cores and slices your favorite stone fruit in one swift push.
Compare with similar items
This Item  Amco Advanced Performance Measuring Cups Baking Supplies, Multisizes, Silver |  |  |  |  |  | |
| Price | -30% $15.10 Typical: $21.58 | $20.99 | -20% $27.15 Typical: $34.00 | $20.99 | $21.99 | $15.99 |
| Delivery | Get it as soon as Tuesday, May 14 | Get it as soon as Tuesday, May 14 | Get it May 15 - 16 | Get it as soon as Tuesday, May 14 | Get it as soon as Tuesday, May 14 | Get it as soon as Tuesday, May 14 |
| Customer Ratings | ||||||
| Sturdiness | ||||||
| Easy to clean | ||||||
| Easy to read | ||||||
| Accuracy | ||||||
| Sold By | Amazon.com | KALSREUI | Sur La Table (dba) | Nstezrne | ALLWIN-HOUSEWARE | Elliott Bay Online |
| material | Stainless Steel | Stainless Steel | Stainless Steel | Stainless Steel | Stainless Steel | Stainless Steel |
| number of pieces | 1 | 7 | 4 | 5 | 13 | 1 |
| capacity | 0.24 liters | 240 milliliters | — | 250 milliliters | 5 milliliters | 236 milliliters |
| weight | 0.98 pounds | — | 0.98 pounds | — | 570 grams | — |
Reviews with images
Accurate High Quality Cups
The following review was written on Apirl 30, 2009, but for some reaons Amazon broke the link between the product and the review, and was unable to link them back. Because many readers find the original review helpful, it is reposted here. Hope it will helpful to you as it was helpful to them:The AMCO Advanced measuring cups and spoons are great. They are made with high quality thick 18/10 stainless steel. The steel is more than 1 mm thick, so they are heavy and sturdy. Each cup or spoon is made from a single-piece steel (no weld nor seam), so it is very easy to clean - a simply wipe will do. The size/volume markings are engraved into the metal, so they will not fade. I have uploaded a picture of a 1-cup for customer image. These tools should last you a lifetime.Comparing to typical measuring cups, these cups are shorter and wider, which allow them to balance nicely on a flat surface. The ends of the spoon handles are bended downward, so the spoons can sit nicely on a flat surface. This comes handy from time to time, more so for cooking than baking - in my experience.I feel there is a need to address some of the negative reviews here. While I agree with many of them, I do not experience some of the more detrimental ones.I find my cups and spoons to be reasonably accurate. I used a graduating cylinder to measure the 1 cup because its filled weight exceeds the limit of the analytical balance. For the 1 cup which should equal to 236mL, I measured a volume of ~222mL. This is a -6% deviation. For the rest of the cups and spoons, I filled them with water and poured the water into a container for weight measurement. The weight is then converted back to volume via "1 gram of water = 1 mL of water". (These measurements were acquired from an analytical scale in a laboratory. These analytical scales are routinely calibrated and are more accurate than the typical kitchen scales.)For the ½ cup (118mL), I measured a volume of 111.5mL (a -6% deviation).For the 1/3 cup (79mL), I measured 84.8mL (+7%).For the ¼ cup (59mL), I measured 61.8mL (+5%).For the 1 tablespoon (15 mL), I measured 14.0mL (-7%).For the 1 teaspoon (5mL), I measured three times and the averaged volume is 4.7mL (-6%).For the ½ teaspoon (2.5mL), I measured 2.5mL (0%).For the ¼ teaspoon (1.25mL), I measured 1.4mL (+12%).Specifically, the 1 teaspoon measurement was repeated three times. The individual results were: 5.2mL, 4.5mL, and 4.3mL. This illustrates the variability introduced by a user -- human error. These cups and spoons appear to be adequate for ~10% accuracy.I find the cups and spoons have smooth surface, and did not find any rough edge or surface as mentioned by other reviewers.Now I will confirm some of the negative reviews. Yes, these cups and spoons are heavier than any I have seen. They are about 2-3 times heavier. Due to the fact that the cups are wider, you may also have difficulty to get them into containers with small opening. This is especially so for the 1-cup, which is 3-7/8 inches wide (I have upload a customer picture of it). Because the cups are shorter and wider, the potential for measurement error is higher. Imagine you have a tall bottle and a flat bowl. If you are 1 cm off from filling up the tall bottle, the relative error will be minor. However, if you are 1 cm off from filling up the flat bowl, the relative error will be large. Since these cups are about ½ the height of other cups, the potential human error is about 2-fold higher. One may say, these cups and spoons are technically accurate, but the potential human error is magnified.*Update on Jun 26, 2010* Everything is working fine. Nothing is broken.
Top reviews from the United States
There was a problem filtering reviews right now. Please try again later.
Reviewed in the United States on January 24, 2011
The following review was written on Apirl 30, 2009, but for some reaons Amazon broke the link between the product and the review, and was unable to link them back. Because many readers find the original review helpful, it is reposted here. Hope it will helpful to you as it was helpful to them:
The AMCO Advanced measuring cups and spoons are great. They are made with high quality thick 18/10 stainless steel. The steel is more than 1 mm thick, so they are heavy and sturdy. Each cup or spoon is made from a single-piece steel (no weld nor seam), so it is very easy to clean - a simply wipe will do. The size/volume markings are engraved into the metal, so they will not fade. I have uploaded a picture of a 1-cup for customer image. These tools should last you a lifetime.
Comparing to typical measuring cups, these cups are shorter and wider, which allow them to balance nicely on a flat surface. The ends of the spoon handles are bended downward, so the spoons can sit nicely on a flat surface. This comes handy from time to time, more so for cooking than baking - in my experience.
I feel there is a need to address some of the negative reviews here. While I agree with many of them, I do not experience some of the more detrimental ones.
I find my cups and spoons to be reasonably accurate. I used a graduating cylinder to measure the 1 cup because its filled weight exceeds the limit of the analytical balance. For the 1 cup which should equal to 236mL, I measured a volume of ~222mL. This is a -6% deviation. For the rest of the cups and spoons, I filled them with water and poured the water into a container for weight measurement. The weight is then converted back to volume via "1 gram of water = 1 mL of water". (These measurements were acquired from an analytical scale in a laboratory. These analytical scales are routinely calibrated and are more accurate than the typical kitchen scales.)
For the ½ cup (118mL), I measured a volume of 111.5mL (a -6% deviation).
For the 1/3 cup (79mL), I measured 84.8mL (+7%).
For the ¼ cup (59mL), I measured 61.8mL (+5%).
For the 1 tablespoon (15 mL), I measured 14.0mL (-7%).
For the 1 teaspoon (5mL), I measured three times and the averaged volume is 4.7mL (-6%).
For the ½ teaspoon (2.5mL), I measured 2.5mL (0%).
For the ¼ teaspoon (1.25mL), I measured 1.4mL (+12%).
Specifically, the 1 teaspoon measurement was repeated three times. The individual results were: 5.2mL, 4.5mL, and 4.3mL. This illustrates the variability introduced by a user -- human error. These cups and spoons appear to be adequate for ~10% accuracy.
I find the cups and spoons have smooth surface, and did not find any rough edge or surface as mentioned by other reviewers.
Now I will confirm some of the negative reviews. Yes, these cups and spoons are heavier than any I have seen. They are about 2-3 times heavier. Due to the fact that the cups are wider, you may also have difficulty to get them into containers with small opening. This is especially so for the 1-cup, which is 3-7/8 inches wide (I have upload a customer picture of it). Because the cups are shorter and wider, the potential for measurement error is higher. Imagine you have a tall bottle and a flat bowl. If you are 1 cm off from filling up the tall bottle, the relative error will be minor. However, if you are 1 cm off from filling up the flat bowl, the relative error will be large. Since these cups are about ½ the height of other cups, the potential human error is about 2-fold higher. One may say, these cups and spoons are technically accurate, but the potential human error is magnified.
*Update on Jun 26, 2010* Everything is working fine. Nothing is broken.
The AMCO Advanced measuring cups and spoons are great. They are made with high quality thick 18/10 stainless steel. The steel is more than 1 mm thick, so they are heavy and sturdy. Each cup or spoon is made from a single-piece steel (no weld nor seam), so it is very easy to clean - a simply wipe will do. The size/volume markings are engraved into the metal, so they will not fade. I have uploaded a picture of a 1-cup for customer image. These tools should last you a lifetime.
Comparing to typical measuring cups, these cups are shorter and wider, which allow them to balance nicely on a flat surface. The ends of the spoon handles are bended downward, so the spoons can sit nicely on a flat surface. This comes handy from time to time, more so for cooking than baking - in my experience.
I feel there is a need to address some of the negative reviews here. While I agree with many of them, I do not experience some of the more detrimental ones.
I find my cups and spoons to be reasonably accurate. I used a graduating cylinder to measure the 1 cup because its filled weight exceeds the limit of the analytical balance. For the 1 cup which should equal to 236mL, I measured a volume of ~222mL. This is a -6% deviation. For the rest of the cups and spoons, I filled them with water and poured the water into a container for weight measurement. The weight is then converted back to volume via "1 gram of water = 1 mL of water". (These measurements were acquired from an analytical scale in a laboratory. These analytical scales are routinely calibrated and are more accurate than the typical kitchen scales.)
For the ½ cup (118mL), I measured a volume of 111.5mL (a -6% deviation).
For the 1/3 cup (79mL), I measured 84.8mL (+7%).
For the ¼ cup (59mL), I measured 61.8mL (+5%).
For the 1 tablespoon (15 mL), I measured 14.0mL (-7%).
For the 1 teaspoon (5mL), I measured three times and the averaged volume is 4.7mL (-6%).
For the ½ teaspoon (2.5mL), I measured 2.5mL (0%).
For the ¼ teaspoon (1.25mL), I measured 1.4mL (+12%).
Specifically, the 1 teaspoon measurement was repeated three times. The individual results were: 5.2mL, 4.5mL, and 4.3mL. This illustrates the variability introduced by a user -- human error. These cups and spoons appear to be adequate for ~10% accuracy.
I find the cups and spoons have smooth surface, and did not find any rough edge or surface as mentioned by other reviewers.
Now I will confirm some of the negative reviews. Yes, these cups and spoons are heavier than any I have seen. They are about 2-3 times heavier. Due to the fact that the cups are wider, you may also have difficulty to get them into containers with small opening. This is especially so for the 1-cup, which is 3-7/8 inches wide (I have upload a customer picture of it). Because the cups are shorter and wider, the potential for measurement error is higher. Imagine you have a tall bottle and a flat bowl. If you are 1 cm off from filling up the tall bottle, the relative error will be minor. However, if you are 1 cm off from filling up the flat bowl, the relative error will be large. Since these cups are about ½ the height of other cups, the potential human error is about 2-fold higher. One may say, these cups and spoons are technically accurate, but the potential human error is magnified.
*Update on Jun 26, 2010* Everything is working fine. Nothing is broken.
Images in this review
Reviewed in the United States on March 6, 2024
Reviewed in the United States on April 3, 2014
